|
|
Post by muxter on Feb 24, 2009 21:05:25 GMT 1
Greetings everyone.
My title gives out on the subject I guess. Can parts from NTV be fitted on Revere model? Namely handlebars and instruments. If yes, what else should I be buying from the guy braking the NTV? Is it complete front or just some parts?
I hope I make sense...
Ride well
Mux
|
|
|
|
Post by Jaz66 on Feb 24, 2009 21:40:08 GMT 1
Hi Muxter sure some one who knows more will respond, until then i would recommend using search, to hunt down likely posts. I did that and found this if it is of any help. Not sure clocks or handlebars are interchangeable, pretty sure its a NO on that front, but hey, I could be wrong.... ;D Raising the handlebars |
|
|
|
Post by muxter on Feb 24, 2009 21:52:22 GMT 1
Thank you Jaz.
I've read the article on raising the handlebars. It's doesn't help me at this point. I'm wondering if I can change the top yoke as well, and then fit NTV clocks and handlebar etc etc? Or do I need to buy top and bottom yoke, with the axle in between? Well more or less complete front end, minus forks. Because it seems that this guy sells NTV parts, need to verify on that. Or it's going to be new aftermarket clocks for me.
|
|
|
|
Post by rj2para (Bisto) on Feb 24, 2009 21:58:39 GMT 1
Not the best pic off my bike but it will show the difference in the bars.  "click on the image to see her large" Happy to post more if there are specific parts you want to compare. Thats me done  Roger. |
|
|
|
Post by rj2para (Bisto) on Feb 24, 2009 21:59:50 GMT 1
I am sure I have seen some clocks on ebay. amy be worth a look.
|
|
|
|
Post by muxter on Feb 24, 2009 22:12:50 GMT 1
@ rj2para : Yea same bars as mine. Sadly buying on e-bay, UK sellers, is not really an option for me. I seen some clocks there as well. But it's to much trouble buying them and then shipping them here. It goes way over the cost of aftermarket, new, clock made by KOSO.
Ah well I'll keep hunting.
Thx again for the answers.
|
|
|
|
Post by rj2para (Bisto) on Feb 24, 2009 23:20:19 GMT 1
Sorry mate good luck in your hunt.
R.
|
|
|
|
Post by Buzzin (^_^) on Feb 25, 2009 14:11:29 GMT 1
Technicly the clocks and handlebars should fit the Revere.
BUT! The topyolk (that the word? the bit that clamps on the front suspension) is different on the Revere/NTV
The Revere one uses a design similar to clip-ons, and doesn't have anywhere to mount 'normal' bars.
Also, the suspension comes up through the topyolk slightly, but this could be changed.
The other problem is the mounting of the clocks. I am not sure, but fairly confident the clockmountingis different.
Problem 3: The fusebox. But mounting Revere parts on an NTV would be easy, other way around would be tricky.
On the revere, the fusebox is inbetween the two bar ends on the top yolk. So it would have to be moved.
On the NTV the fusebox is already somewhere else.
So yes, it is possible, but if you do it, make sure you swap the top-yolk + counters + bars if possible, and you would still need to find a solution for the fusebox.
(ps. I have no idea if the top-yoke can be combined with a bottom one from the other model....or indeed if you can seperate them at all)
|
|
|
|
Post by muxter on Feb 27, 2009 19:44:30 GMT 1
Ahhhh right, the fuse box. Haven't thought about that at all. Bah it would turn out to be way more trouble than it's worth. Better and easier to buy aftermarket set of clocks. Thx for all the answers.
|
|
